Effective gas leak detection in a commercial building cannot depend on someone happening to notice a smell. A slow leak in a ceiling void, plant room or kitchen line can build for weeks before anyone reports it. By then, you are managing an evacuation rather than a planned repair.
For Melbourne facility managers running aged care facilities, schools, manufacturing plants and commercial properties, that gap carries real regulatory and operational risk.
This guide covers the detection methods that work at commercial scale, how often each should happen, the records you need to keep and how to judge when a finding becomes an emergency.
Who Is Responsible for Gas Safety Downstream of the Meter
In Victoria, your gas distributor looks after the supply network up to and including the meter. Everything downstream, including consumer piping, appliances, flues and fixed detection equipment, sits with the owner or occupier. That makes leak detection a facility management obligation, not a utility service.
Energy Safe Victoria (ESV) regulates gas safety under the Gas Safety Act 1997, and the Building and Plumbing Commission licenses the gasfitters who work on your system. ESV generally treats gasfitting in industrial, commercial and public premises, including schools and hospitals, as complex gas installation work.
Under its gas acceptance scheme, complex installations and Type B appliances such as industrial burners and process ovens must be accepted by ESV before gas is supplied.
Detection requirements usually sharpen after a trigger: a new appliance or tenancy fit-out, ageing steel pipework, nearby excavation, an odour complaint or a detector alarm. Ignoring these can lead to compliance notices, infringement penalties or prosecution. An installation found to be unsafe can also be isolated until it is rectified, which takes kitchens, hot water and heating offline.
Typical scenarios include a perished flexible hose behind an aged care combi oven, a school bench gas tap left partly open overnight, and a threaded joint on a manufacturing burner train loosened by vibration. Each can go unnoticed for weeks in a busy, well-ventilated space.
Four Gas Leak Detection Methods for Commercial Facilities
No single method catches every gas leak. A reliable program layers the four methods below so each one covers the gaps in the others.
-
Occupant reports and routine visual checks
Staff remain your first line of detection. Train kitchen, cleaning and maintenance teams to report odours, hissing, yellow flames and pilots that keep dropping out, and give them one clear reporting channel. Repeated pilot failures on a water heater can signal a supply or appliance fault, as explained in our guide to gas hot water not working.
-
Meter and consumption checks
Your gas meter is an underused leak indicator. With appliances off after hours, the meter’s lowest-value dial should not move, so any movement suggests gas is escaping downstream. Pilot flames register a small flow, so have your gas plumber account for them. Between checks, compare monthly consumption against the same period last year and investigate any unexplained rise.
-
Portable gas leak detector surveys
A licensed gasfitter sweeps a calibrated electronic gas leak detector along pipe runs, unions, valves, regulators, flexible hoses and appliance connections. Positive readings are confirmed with leak detection fluid at the suspect joint. Never search for a leak with a naked flame or any device that could create a spark.
-
Pressure (tightness) testing
A tightness test isolates the consumer piping, holds it at a set test pressure and monitors it with a calibrated gauge over a set period. Any pressure drop confirms a leak, even one too small for an instrument survey to locate. AS/NZS 5601.1 sets leak testing requirements after installation or alteration, and the same test is the most reliable way to confirm an existing system is sound.
Fixed Gas Detectors: Placement, Interlocks and Calibration
Fixed detection monitors continuously in areas where gas could build up unnoticed, such as plant rooms, commercial kitchens and basements. Placement depends on the gas. Natural gas is lighter than air and rises, so sensors belong near ceiling level. LPG is heavier than air and pools in pits, drains and basements, so sensors belong near the floor.

In commercial kitchens, the gas supply is commonly interlocked with the exhaust hood so gas cannot flow unless extraction is running. Linking fixed detectors to the same solenoid valve adds automatic shut-off when gas is detected. Where detectors report to your fire indication panel, coordinate testing with your fire systems contractor so both are verified together.
Detectors drift, and sensors have a finite service life. Follow the manufacturer’s calibration and replacement intervals, using AS/NZS 60079.29.2 as the reference for selection, installation and maintenance.
In manufacturing plants, pits and enclosed plant spaces may also be confined spaces, and WorkSafe Victoria’s compliance code for confined spaces explains how to assess and control atmospheric hazards before anyone enters.
Testing Frequencies and the Records Auditors Expect
Base your schedule on your risk profile. The baseline below suits most commercial facilities, but insurer or manufacturer requirements take priority where they are stricter.
- Every shift: kitchen and plant staff check flame colour, odour and the detector panel status.
- Monthly: compare meter reads with your consumption baseline and inspect exposed pipework and flexible hoses.
- Six-monthly: function test fixed detectors, alarms and shut-off valves, or at the interval the manufacturer specifies.
- Annually: a licensed gas plumber completes an inspection, portable detector survey and tightness test, with higher-risk sites tested more often.
- After any gas work, alteration or alarm: a tightness test before the system returns to service.
Keep every record in one register: test results, detector calibration certificates, ESV acceptance records for complex installations and a defect log showing how each issue was closed out. For standard gas installations, work on consumer piping or Type A appliances requires a compliance certificate issued to you within five days of completion.
We record every gas job in SimPRO, so your reports carry time-stamped results, photos and the gasfitter’s licence details, ready for an audit or insurance claim.
Detection Priorities for Aged Care, Schools and Manufacturing
In aged care facilities, residents may have a reduced sense of smell or be unable to report an odour, so fixed detection in kitchens, laundries and hot water plant rooms carries more weight. Schedule testing around meal service and personal care, and plan isolations so residents keep access to hot water.
In schools, science laboratories with bench gas taps are a recurring leak point. Confirm the master isolation valve is closed at the end of each day, and book tightness testing for school holidays to avoid disrupting classes.
In manufacturing plants, Type B appliances, higher operating pressures, vibration and thermal cycling all stress joints. Align surveys and tightness tests with planned shutdowns to protect production continuity.
For commercial property and student accommodation, tenant fit-outs and high-use central hot water plant are the usual weak points. Require documentation for any tenant gas work and include rooftop plant in every survey.
Warning Signs That Need an Immediate Response
Let severity drive your response. Sorting findings into three tiers helps your team act consistently, including after hours.
Act immediately if you have:
- A strong gas odour, hissing sound or fixed detector alarm.
- Occupants reporting headaches, dizziness or nausea near gas appliances.
- Gas pipework damaged by works, impact or excavation.
Evacuate, isolate the gas at the meter if it is safe to do so and avoid operating electrical switches. Call 000 if there is any risk to life, then your distributor’s emergency number printed on your gas bill. Once the area is safe, engage a licensed emergency plumber in Melbourne to locate and repair the leak.
Book a same-day visit for meter movement with appliances off, a faint or intermittent odour, repeated pilot outages, or yellow flames and soot. Overdue calibrations, minor pipe corrosion and missing test records belong in your next scheduled maintenance visit, not a callout.

How VIP Plumbing Group Handles Commercial Gas Leak Detection
Our licensed gasfitters follow four stages: assessment, testing, documentation and certification. We start by mapping your meter, isolation valves, appliances and detectors, then complete instrument surveys and tightness testing around your operating hours.
Results and photos are recorded in SimPRO and issued as a digital report, with compliance certificates or ESV documentation completed for any gasfitting work. Repairs are prioritised by risk, and each defect stays on your register until it is closed out.
“In more than 30 years of commercial work, the leaks that concern me most are the ones nobody can smell. They sit in a ceiling void or behind a kitchen line for months. Regular testing and a proper paper trail turn that hidden risk into a planned repair instead of an evacuation.” – Darren Walton, General Manager and Owner, VIP Plumbing Group
Because we specialise in commercial facilities, our team plans around aged care routines, school calendars and production schedules. We service sites Melbourne-wide with priority emergency response for contracted clients, and can build detection into your commercial maintenance program alongside routine general plumbing work.
Gas Leak Detection Compliance Checklist
- Keep a current gas plan for each site showing the meter, isolation valves, appliances and fixed detectors.
- Book a licensed inspection, detector survey and tightness test at least annually, and after any gas work or alarm.
- Function test fixed detectors and kitchen interlocks six-monthly or as the manufacturer specifies.
- Hold compliance certificates, ESV acceptance records, test results and calibration certificates in one register.
- Display your distributor’s emergency number at every gas isolation point and include it in site inductions.
- Ask contractors for their gasfitting licence class, Type B experience where relevant, tightness test method and reporting format.
Book a Gas Leak Detection Assessment for Your Facility
Structured gas leak detection protects your occupants, keeps your records audit-ready and turns hidden leaks into planned repairs instead of shutdowns. For broader context on warning signs, emergency steps and Victorian compliance, read our guide to commercial gas leak signs, steps and compliance.
VIP Plumbing Group can assess your facility, test your gas installation and deliver the documentation your auditors and insurers expect. Call 1800 319 522 or request a quote to arrange a free facility assessment.

